六合历史开奖记录

咨询热线:

0531-88771136

您的当前位置: 首页 > 新闻中心 > 正文

模具装配线标准规范都有哪些呢?

来源:六合历史开奖记录    发布时间:2019-12-26 15:20:59    点击:

山东模具装配线标准规范
  Shandong mould assembly line standard specification模具装配线后,应超过以下关键标准:
  After die assembly line, the following key standards shall be exceeded:
  (1)标准件的装配线应可靠。地脚螺栓的螺杆长度应不小于连接铸铁时地脚螺栓的直径,且不小于连接铸铁时地脚螺栓直径的1.5倍;销子与各部件的配合长度应超过销子直径的1.5倍;地脚螺栓和销钉的内孔不得露出上、下模座等零件的表面。
 
  (1) The assembly line of standard parts shall be reliable. The screw length of the anchor bolt shall not be less than the diameter of the anchor bolt when connecting the cast iron, and shall not be less than 1.5 times of the diameter of the anchor bolt when connecting the cast iron; the matching length of the pin and each component shall be more than 1.5 times of the diameter of the pin; the inner hole of the anchor bolt and the pin shall not expose the surface of the upper and lower mold bases and other parts.
  (2)落料孔或进给槽应平整,保证生产或废料能随意排出。
 。2) The blanking hole or feed groove shall be flat to ensure that the production or waste can be discharged at will.
  (3)交换标准。螺钉的拧紧和两者之间销孔的精确定位都应正常良好。
  (3) Exchange standards. The screw tightening and the precise positioning of the pin hole between the two should be in good condition.
  (四)压床磨具的安装规范应符合机器设备使用规定;起重部件应可靠。
 。4) The installation specification of the grinding tool of the press shall conform to the use regulations of the machine and equipment; the lifting parts shall be reliable.
  (5)磨料按制造标准检验,生产符合设计方案要求。
  (5) The abrasives are inspected according to the manufacturing standards, and the production meets the requirements of the design scheme.
六合历史开奖记录_山东模具
  (6)模具架精度符合国家行业标准(LF/T8050—1998《五金模具架技术标准》;LF/T8071—1997五金模架精度检验)。五金模具的高宽比应符合工程图纸要求。
  (6) The accuracy of mold base conforms to the national industry standard (LF / t8050-1998 technical standard for metal mold base; LF / t8071-1997 precision inspection for metal mold base). The height width ratio of hardware mould shall meet the requirements of engineering drawing.
  (7)装配线五金模具好,底部模具沿定位销向上、向下拖动应稳定、可靠。
  (7) The hardware mould of the assembly line shall be good, and the bottom mould shall be stable and reliable when it is dragged up and down along the locating pin.
  (8)凹模与凸模之间的空隙应符合工程图纸要求,并均匀铺展。模架或模腔的工作按技术标准的要求进行布置。
  (8) The gap between the die and the punch shall meet the requirements of the engineering drawing and be spread evenly. The work of mold base or cavity shall be arranged according to the requirements of technical standards.
  (9)支挡设备的准确定位及相对位置应符合工程图要求。冷冲压模具导板间距与工程图纸相同;导轨面应与模具进给轴承轴线平行;导向板带有侧压装置,侧压板应便于拖动,工作可靠。
  (9) The accurate positioning and relative position of retaining equipment shall meet the requirements of engineering drawing. The distance between guide plates of the cold stamping die is the same as that of the engineering drawing; the guide rail surface shall be parallel to the axis of the feed bearing of the die; the guide plate is equipped with side pressing device, and the side pressing plate shall be easy to drag and work reliably.
  (12)相对的部分倒和升降设备应符合设计方案,多余的宽度应在允许的要求,也没有偏转和单边偏转不得标题脸上,确保生产或浪费可以立即删除并成功。
  (12) The relative part reversing and lifting equipment shall conform to the design scheme, and the redundant width shall meet the allowable requirements, and shall not be placed on the title face without deflection and unilateral deflection, so as to ensure that the production or waste can be deleted immediately and successfully.
  以上就是对山东模具装配线标准规范的详细介绍,想要了解更多请点击官网
The above is a detailed introduction to the standard specifications of Shandong mold assembly line. For more information, please click
联系我们 contact

六合历史开奖记录查询

电话1:13173017488

电话2:18615459955

传真:0531-88771136

邮箱:hlm369@126.com

地址:山东省济南市大桥镇大王村北跨商务中心后三层白楼

六合历史开奖记录查询 手机: 13173017488 咨询热线: 0531-88771136 咨询热线:18615459955 邮箱:hlm369@126.com

公司地址: 山东省济南市大桥镇大王村北跨商务中心后三层白楼 备案号:鲁ICP备19048961号-1

版权所有 Copyright ? 2016-2018 六合历史开奖记录查询 网站建设:济南诺商 流量统计:
网站地图XMLTXT

六合历史开奖记录-六合历史开奖记录查询-2020年香港历史开奖记录版
Baidu
sogou